The DSP is the Digital Signal Processing chip If it finds a board at the given address, Daqarta checks the DSP Help system without having a board installed or The only exception is if you set A:0 to allow Sound Blaster 16/32/64 board not found at 0240h. Used if there is no BLASTER string and no A: parameter.ĭaqarta checks at the address given, and if itĭoes not find a valid Sound Blaster-compatibleīoard there it exits with a message giving the address it tried: The default address for SB16.ADC is hex 220, which will be 'h' prefix before hexadecimal values, as in:Ĭompare this to the BLASTER format, which would be just A240. If you do need to give the A: parameter here, note that allĭaqarta parameters require a colon, and that you should use an Sound card installed, and the single BLASTER string is for The most likely reason for theīLASTER string being wrong is that you have more than one The A parameter in the BLASTER string must correspond to theīase address of the card, whether set via jumpers on the card (You can view all the strings in the environment Manager that may be invoked from either AUTOEXEC.BAT or fromĬONFIG.SYS. For PnP cards BLASTER is set by the CTCM configuration This normallyĪppears as a SET BLASTER= line in AUTOEXEC.BAT for non-PnPĬards. You only need to give this parameter if the BLASTER string Use this to tell Daqarta the base I/O address for your SB16 Information summary available via the ALT-H String, configuration line, or default, by checking the board Once Daqarta is running, you canĬheck to see which parameters have been set by the BLASTER This actually sets the physical address of the card,Īnd without it the card is invisible to your system.ĭaqarta will exit with an error message if it finds a problem The configuration manager must appear in CONFIG.SYS orĪUTOEXEC.BAT to configure the PnP card properly before Daqarta WavEffects boards may require an H: parameter, however.) Since these are read directly from the board and can only beĬhanged by the PnP configuration manager. On PnP cards, the D:, H:, and I: parameters will be ignored, Later you can add parameters for advanced features. On most systems, you can probably omit all parameters andĪccept the BLASTER values when you are getting started. You can view theīLASTER string by entering SET at the DOS prompt. Than one sound card in your system, since there will be only You may need to override the BLASTER settings if there is more Value to be used in preference to the equivalent BLASTERĪllows you to set a different mixer address. Setting anĪ:, I:, D:, or H: value on the SB16.ADC line will cause that The mixer chip uses a different address than the DSP, which isĪ possibility with PnP models, then the BLASTER string willĪlso include an M value which Daqarta will use. Present, and use that to set the Address, If you don't also use a B: Bits parameterĭaqarta will read the BLASTER environment string, if it is The order of the parameters is generally not important, exceptĪs noted below for the D: and H: parameters Use one or more spaces to separate parameters.
Each parameter is given as a letter and colon, followed SB16.ADC line, which must be the second line of theįile.
#Sound blaster software dos driver#
This driver allows you to specify certain parameters on the Stimulus Source Preset, STIM3 or OP元 Synth.Sample Rate Calibration (Advanced Users).Clearing or Keeping Board Registers (Advanced Users).DMA Level (8-bit), High DMA Level (16-bit) and IRQ.Use another method to determine the base address of the
Second sound card, or you use another configuration manager The A: parameter may be needed if you are using a It reads the base address of the card from theīLASTER environment string, which should be set by a PnPĬonfiguration manager such as CTCM, or via a SET BLASTER= This driver does not directly configure PnP (Plug 'n Play)Ĭards. This driver also allows optional LPT printer port use for This feature is supported by means of special hardware that is Providing simultaneous 16-bit ADC inputs and DAC outputs. you can't have both the same.Ĭreative Labs WavEffects and ViBRA models CT4170, CT4171, andĬT4172 do allow both ADC and DAC bit widths to be the same, (Alternatively, it can produce stimuli from theĨ-bit DAC outputs with 16-bit ADC inputs, or 16-bit DAC Supported via special SB16.ADC configuration parameters. Specifications, some of which are undocumented (such as data Models (more than 50) that are nominally compatible with thisĭriver. The Creative Labs product line includes a wide variety of Including Sound Blaster PnP models, Sound Blaster 32, Soundīlaster 64, ViBRA, WavEffects, etc. This driver was specifically designed for the Creative Labs
#Sound blaster software dos windows#
Daqarta for DOS: SB16 Sound Blaster 16 Driverĭaqarta for DOS Data AcQuisition And Real-Time Analysis Shareware for Legacy Systems (Use Daqarta for Windows with modern systems)
0 kommentar(er)
